Cura edition octoprint Q's
Note: this is not an official support forum. See below for official resources/channels
im looking for a website where i can find this book please
Community for sharing free text books
so I'm here trying to use this method to get the complete length of my cable. I remember the amount of loops diameter and pie but how to plug it all in I might need a better breakdown please electrical team thank yall lots
Welcome to /r/AskElectricians. To get verified, send a photo to the mods that has your certificate/seal/card. In this photo, have a piece of paper with your username and date written on it. Block out all identifying information. Once verified delete the image. If the instructions are not followed exactly, the request will be ignored.
Tesla type 2 charger what is the best type of #6 awg and plug similar to this to install please help #ELECTRICALTEAM
Welcome to /r/AskElectricians. To get verified, send a photo to the mods that has your certificate/seal/card. In this photo, have a piece of paper with your username and date written on it. Block out all identifying information. Once verified delete the image. If the instructions are not followed exactly, the request will be ignored.
Longer hotend / Spider High Temperature and High Flow Hotend Pro compatibility
Welcome to LONGER, leader of innovation in laser engravers and 3D printers
Hey Y'all I got the LK5 PRO it was fully functional. Until a tear drop of water from my build plate set off something like this message before us here I tested the build plate with my multimeter It's still functional.
The place to discuss all stuff related to the Nintendo 3DS™ family!
Hey Y'all I got the LK5 PRO it was fully functional. Until a tear drop of water from my build plate set off something like this message before us here I tested the build plate with my multimeter It's still functional.
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Hey Y'all I got the LK5 PRO it was fully functional. Until a tear drop of water from my build plate set off something like this message before us here I tested the build plate with my multimeter It's still functional.
Welcome to LONGER, leader of innovation in laser engravers and 3D printers
First time using PETG STILL UNSUCCESSFUL:(
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
Hey everyone , I have a bit of an issue with a failed Print while using octoprint. What I'm trying to figure out is how can I find the g code that I last used. If someone can give me a breakdown it would be very helpful seeing that the print is only one day and hours type of build?? I tied going on
Note: this is not an official support forum. See below for official resources/channels
Hey yall I'm having trouble with my printer which I have on 10 % infill 4 layer and top and bottom wall count 2-3 . For some reason I get this result which makes the build weaker. How can I go about this with using Cura anyone ?
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
RASBERRY PI CONFIGURATION
Note: this is not an official support forum. See below for official resources/channels
pi help
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The cura slicer /G Code to provide a later change but when it gets to the layer height it reacts like this and can no longer function #LK5 PRO
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
How can I successfully save on inkscape to ESTLCAM without this issue please yall 😫
An online community of Inkscape users with discussion, tutorials, and shared creations made with Inkscape: a free and open-source SVG editor.
hey yall I'm stuck trying to find the most affordable 2 flute upcut spiral 1/4" or even 3/8 router bit for my Makita RT0701C Compact Router. I have had no luck at all with this mess
For anything CNC related: CAD, CAM, automation, and more!
Best Engineering calculator for Router
For anything CNC related: CAD, CAM, automation, and more!
Hey everyone, so I'm using ESTLCAM and i keep getting this when i attempt to create a g code but is there another way ?? To create a g code properly ? How does it get to look like the actual file that marks as g code ?? Can I also do it through Inkscape because it's not allowing me to do it on that
For anything CNC related: CAD, CAM, automation, and more!
How fast should I be cutting polycarbonate? I've never cut it before, and don't want to start off out in left field. Keep in mind I'm using 1/4" for a Makita router
For anything CNC related: CAD, CAM, automation, and more!
How fast should I be cutting polycarbonate? I've never cut it before, and don't want to start off out in left field. keep in mind I'm using the 1/4" setting for a makita
For anything CNC related: CAD, CAM, automation, and more!
The resourceful FREE CNC PROM
For anything CNC related: CAD, CAM, automation, and more!
Help an begginer out I need it to be solid all over like the silver block but I keep getting it turned into the blue object with no top layer from cura???
/r/3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
What steps to get through this bowton tube!!
Anything to do with Anycubic 3d printers. Unofficial, not affiliated with Anycubic.